Sherwood V-903 User Manual download pdf (Page 7)

Notes :

• To listen to digital audio signal that is outputting from the

DIGITAL OUTs, you should set the AUDIO OUT to

“SPDIF/BITSTREAM” or “SPDIF/PCM”.(In this case, the

analog audio signal cannot be output from the AUDIO OUTs

of this unit.)

When the AUDIO OUT is not set correctly, loud noise or no

sound may be heard from the speakers, and it may be

harmful to your ears and damages the speakers.(Refer to

“SETTING THE AUDIO SETUP” on page 33.)

• When you connect the MD or CD recorder with a digital

input for digital recording, the AUDIO OUT should be set to

SPDIF/PCM. If not, the digital recording do not perform

properly. (Refer to “SETTING THE AUDIO SETUP” on

page 33.)

• When making the COAXIAL DIGITAL connection, be sure

to use a 75Ω COAXIAL cord, not a conventional AUDIO

cord.

• All of the commercially-available optical fiber cords cannot

be used for audio equipments. If there is an optical fiber

cord which cannot be connected to your audio equipments,

consult your dealer or nearest service organization.

󳂮󳂮

Audio output from the unit’s DIGITAL OUTs

Note 1 : The type of audio output from the DIGITAL OUTs

can be selected by the AUDIO OUT settings.

Note 2 : Sound having 96 kHz sampling is converted into 48

kHz sampling when it is output from the unit’s

DIGITAL OUTs.(Refer to “SETTING THE AUDIO

SETUP” on page 33.)

• Linear PCM is a signal recording format used in music

CDs. While music CDs are recorded in 44.1 kHz/16 bit,

DVD Videos are recorded in 48 kHz/16 bit to 96 kHz/24 bit.

4. AC INPUT CORD

Plug this cord into a wall AC outlet.

5. A/V SCART OUTPUT CONNECTOR (Regional

Option)

Refer to “CONNECTING TO TV WITH SCART

CONNECTOR(Regional Option)” on page 8.

ENGLISH

1. Connecting AUDIO OUTs

Connect these jacks to the AUDIO INs of DVD(, AUX, CD,

etc.) of your amplifier or receiver.

Notes :

• To listen to analog audio signal that is outputting from the

AUDIO OUTs, you should set the AUDIO OUT to

“ANALOG”.(In this case, the digital audio signal cannot be

output from the DIGITAL OUTs of this unit.)

• Depending on whether the AUDIO OUTs are connected to

a stereo amplifier/receiver/TV or a A/V amplifier/receiver

with built-in surround decoder, you should set the

DOWNMIX correctly. (Refer to SETTING THE AUDIO

SETUP” on page 33.)

2. Connecting VIDEO OUTs

The COMPONENT VIDEO OUTs of this unit are capable of

outputting either conventional interlacing video signal or

progressively scanned video signal(that can reproduce high-

density pictures with less flicker).

• According to VIDEO OUTs, the excellence in picture

quality is as follows:

Progressive “COMPONENT” > Interlaced “COMPONENT”

> “S-VIDEO” > “(composite) VIDEO”

• When making COMPONENT VIDEO connections, connect

“Y” to “Y”, “C

B” to “C

B”(, “P

B”, “B-Y”), “CR

” to “CR

”(, “PR”, “R-

Y”).

• Depending on the type of the COMPONENT VIDEO INs of

TV, be sure to set the component video output signal to

the corresponding setting.(Refer to “CHANGING THE

COMPONENT VIDEO OUTPUT SIGNAL” on page 26.)

• If there are both VIDEO INs and (MONITOR) VIDEO OUTs

on your amplifier or receiver, connect these jacks to the

corresponding VIDEO IN jacks of your amplifier or receiver

and (MONITOR) VIDEO OUT jacks of that to the

corresponding VIDEO IN jacks of the TV respectively.

• If there are no VIDEO jacks, connect these jacks to the TV

directly. (Refer to “CONNECTING TO TV WITH AUDIO

AND VIDEO INS” on the next page.)

Notes:

• When the component video output signal is set to

PROGRESSIVE TV, the S-VIDEO and (composite) VIDEO

OUTs can not output the normal video signals. Therefore,

it causes the picture to break up and shake.

• When the progressive video signals are input into the non-

progressive COMPONENT VIDEO INs of your TV, the

picture may not be shown normally, too.

Therefore, when the progressive COMPONENT VIDEO

INs of TV are not connected to, you should set the

component video output signal to INTERLACE TV.

• Do not connect the unit to the TV through a VCR.

Otherwise the picture may be disturbed due to the copy

protection function.

3. Connecting DIGITAL OUTs

You can enhance the sound quality by connecting these

COAXIAL and OPTICAL DIGITAL OUTs to the corresponding

DIGITAL INs of an amplifier, MD recorder, etc.

The digital audio signal from a disc is directly transferred. If

you connect to a DTS or Dolby Digital decoder or an

amplifier with built-in decoder, you can enjoy theater-quality

audio in your home.

Disc

Audio recording

format

Audio output

DVD

Video

Dolby Digital

Dolby Digital bitstream (2~5.1ch) or

PCM(48 kHz/16bit) (2ch) (Note 1)

DTS bitstream or PCM(48 kHz/ 16

bit) (2ch) (Note 1)

PCM(48 kHz/ 16 bit) (2ch) (Note 1)

Linear PCM (48 kHz/16bit) (2ch)

(Note 2) or original signal

Linear PCM (44.1 kHz)

DTS

Linear PCM

(48/96 kHz,

16/20/24bit)

MPEG-2

Linear PCM

CD /

MP3 disc

1 2 3 4 5 6 7 8 9 10 11 12 ... 45 46

Comments to this Manuals

No comments

Sherwood V-903 User Manual Page 7

Comments to this Manuals

Related products and manuals for DVD players Sherwood V-903