EG40-070SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T
Maintenance And ServiceFUEL CONVERSION:Figure 9: Removing valve cap.a) Remove the main burner orice with a inch deep socket.b) Put a bead of pipe-t
11Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 10), rotate it counter-
Initial InstallationQUALIFIED INSTALLERS ONLYWARNING: Operation of this heater when not connected to a properly installed and maintained venting syste
VerticalTerminationStorm CollarFlashingRound SupportBox/Wall ThimbleCeiling FirestopPipelengthPipelengthCathedral CeilingSupport BoxPipelengthRound Su
14MOBILE HOME INSTALLATION:• When the unit is installed in a Mobile Home it must be grounded to the steel chassis or connected to a g
1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.2 In accordance with the current ANSI Z223.1 NFPA 54, National Fu
Figure 19: Wire Spacers.Figure 20: Wire Spacer in Place.the structure. 5. Project a level line from the center point of the elbow. Using
17Initial InstallationQUALIFIED INSTALLERS ONLYFigure 21: Assembly of Venting Kit.Wall framingHorizontal wallterminationWall thimblefire stopInside fi
Initial InstallationQUALIFIED INSTALLERS ONLY1816. Slide the 90° elbow over the ex pipe. Do not slip the outer sections of pipe together, you will re
19Table 4: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).Direct Vent GS Direct-Temp Secure Vent Ameri Vent DirectDescrip
2FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must b
Figure 23: Vent restrictor ring.Figure 22. Possible Vent Congurations; Vertical and Horizontal Terminations.VENT CONFIGURATIONS:Figures 22 shows the
21HORIZONTAL INSTALLATION:1. Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the vent
wall thimble will conceal it (see left image in Figure 26).7. Slide the decorative wall thimble up to the wall surface and attach with th
23VERTICAL INSTALLATION:1. Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, walls, roofs
support straps to the roof. Seal the nails holes heads with non-hardening mastic. Trim the excess length of the support straps that extend out beyond
25NailsCeiling firestopCeilingSecond floorUse clearances to asdefined by appliance andvent pipe manufacturers.• For multi story installations. A
VENTING INTO A CLASS ‘A’ CHIMNEY:This model is also certied and tested to vent into CLASS ‘A’ wood stove chimneys.Place the freestanding direct vent
27
Initial InstallationGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to t
29CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there m
3Table of ContentsSafety Precautions...2Table of Contents...
Secondary InstallationCAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED.Place the log set into the rebox. Locate each log by
31Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas
Parts ListReference NumberPart Description Part Number1 120 °F (49 °C) Ceramic Temperature Sensor EC-0012 S.I.T. NOVA Valve Convertible 50-14213 Ther
33Parts ListReference NumberPart Description Part Number14 Side Panel EG40-086 15 DV Stove Top EG40-087A Firebox Bafe EG40-088Stove Top Bafe DV EG
Parts Diagram - ChassisEG 40 Body (Chassis)July 200434
35Parts Diagram - Gas Tray & DoorEG40 Gas Tray & Door AssembliesJuly 20042782092324510611162625243
WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to t
37Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs
19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a aw and i
39Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________
DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec
5SpecificationsDIMENSIONS:25"(635 mm)21"(533 mm)121/2"(318 mm)45/8"(117 mm)291/8"(740 mm)Shipping Weight 256 lbs (116 kg)Figu
Operating InstructionsFOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.LIGHTING INSTRUCTIONS:61. STOP! Read the safety information above on this label
ThermopileThermocoupleFigure 4: Gas Valve.Figure 3: Pilot Burning.7• There is a separate venturies for each burner, see Figure 5.• Remove one
8Maintenance and ServiceAnnually check to ensure that your Venting system is clear. Periodically check the pilot and burner. Check to see that all the
9Figure 8: Blower (Fan) Removal.1. Turn the unit off, allow it to cool down completely, and remove the door as shown in the MAINTENA
Comments to this Manuals